I'll take a look at the guidelines to contribute, thank you!

@dex Update please the documentation if you want to help project or we'll do it later.
Thanks

The same task T5047

Thank you for the clarification, I will edit my scripts accordingly. I was under the impression that VRRP transition scripts are called with the vyattacfg group out of the box, since there is an example in the documentation which has the sg part missing: https://docs.vyos.io/en/latest/automation/command-scripting.html#run-configuration-commands

We cannot disable keepalived as it is used not only for VRRP and also for virtual-server

set high-availability virtual-server xxxx

So it should be something like set high-availability disable
Or just clean the VRRP configuration with set high-availability vrrp disable

To make sure that a script is not accidentally called without the vyattacfg group, the script can be safeguarded like this:

if [ "$(id -g -n)" != 'vyattacfg' ] ; then
    exec sg vyattacfg -c "/bin/vbash $(readlink -f $0) $@"
fi

https://docs.vyos.io/en/latest/automation/command-scripting.html#executing-configuration-scripts

again. It says - download complete. And i can get it from the message:

In T5045#144137, @aserkin wrote:

Thank you for the hint, @c-po
Attached the entire config we have on the node.

lns-3-1-commands-clean.cfg213 KBDownload

Thank you for the hint, @c-po
Attached the entire config we have on the node.

PR https://github.com/vyos/vyos-1x/pull/1872

Well there should be no harm in lifting the limit of open file descriptors for FRR as its a huge process tree.
Can you share your entire protocols configuration tree so we see what else is configured?

The bfdd process did not start until i changed LimitNOFILE=1024 to LimitNOFILE=2048 in /lib/systemd/system/frr.service
That did the trick, but i'm not sure it's a good solution.
What do you think, @Viacheslav ?

The limits look like standard
root@nn-vlns-3-1:~# ulimit -Hn
1048576
root@nn-vlns-3-1:~# ulimit -Sn
1024
root@nn-vlns-3-1:~# sysctl fs.file-max
fs.file-max = 9223372036854775807

@n.fort I apologize for the late entry here - could this also be exposed for NAT rules?
Edit: wow you guys worked so fast on this it got pulled before I could add this request :D

PR: https://github.com/vyos/vyos-1x/pull/1871

PR https://github.com/vyos/vyos-1x/pull/1870

>>> from vyos.template import range_to_regex
>>> 
>>> range_to_regex(['11-12', '14-15'])
'(1[1-2]|1[4-5])'
>>> 
>>>

I created a separate task for it T5057

The second bug is interface Regex does not work
Get:

interface=re:eth1\.\d+

Expect:

interface=re:^eth1\.(200\d|20[1-9]\d|2[1-9]\d{2}|3000)$

PR https://github.com/vyos/vyos-1x/pull/1869

vyos@r14# run show conf com | match ipoe
set service ipoe-server authentication mode 'noauth'
set service ipoe-server interface eth1 client-subnet '100.64.24.0/24'
set service ipoe-server interface eth1 network 'vlan'
set service ipoe-server interface eth1 vlan '2000-3000'
[edit]
vyos@r14#

Check config:

vyos@r14# cat /run/accel-pppd/ipoe.conf  | grep "\[ipoe" -A 7
[ipoe]
verbose=1
interface=re:eth1\.\d+,shared=0,mode=L2,ifcfg=1,range=100.64.24.0/24,start=dhcpv4,ipv6=1
noauth=1
proxy-arp=1

It is incompatible with static entries.
Maybe it should be fixed after migrating to KEA-DHCP T3316

The similar task T5042

PR:
https://github.com/vyos/vyos-1x/pull/1868

In T3655#143947, @fernando wrote:

it doesn't seem the same problem as here, this logic that was applied over this version was vrf not on the table . Could you share full configuration ? there is some point over vrfs / vrf default /leaking that are not clear. So I can replicate the scenery and we see what is going on .

Needs final testing before PR
https://github.com/vyos/vyos-1x/compare/current...jestabro:literal

it doesn't seem the same problem as here, this logic that was applied over this version was vrf not on the table . Could you share full configuration ? there is some point over vrfs / vrf default /leaking that are not clear. So I can replicate the scenery and we see what is going on .

Possible completions:

<0-4294967295>       DHCP lease time in seconds

Standard lease I have in the configuration is "lease 4294967295"

That is a static reservation. Ensures I have the same IP for a specific host.

VyOS 1.3-stable-202303030442 Works as expected

vyos@r1# run show conf com | match open
set vpn openconnect authentication mode 'radius'
set vpn openconnect authentication radius server 192.168.122.14 key 'vyos-secret'
set vpn openconnect listen-ports tcp '4433'
set vpn openconnect listen-ports udp '4433'
set vpn openconnect network-settings client-ip-settings subnet '100.64.12.0/24'
set vpn openconnect ssl ca-cert-file '/config/auth/ca.crt'
set vpn openconnect ssl cert-file '/config/auth/server.crt'
set vpn openconnect ssl key-file '/config/auth/server.key'
[edit]
vyos@r1# 
[edit]
vyos@r1# run show version all | match ocser
ii  ocserv                               1.1.6-3                        amd64        OpenConnect VPN server compatible with Cisco AnyConnect VPN
[edit]
vyos@r1# 
[edit]
vyos@r1# run show openconnect-server sessions 
interface    username    ip             remote IP        RX      TX         state      uptime
-----------  ----------  -------------  ---------------  ------  ---------  ---------  --------
sslvpn0      foo         100.64.12.225  192.168.122.205  1.3 KB  152 bytes  connected  55s
[edit]
vyos@r1#

PR https://github.com/vyos/vyos-1x/pull/1866

set high-availability vrrp global-parameters notification mail '[email protected]'
set high-availability vrrp global-parameters notification send-faults
set high-availability vrrp global-parameters notification smtp-server address '127.0.0.1'
set high-availability vrrp global-parameters notification smtp-server connection-timeout '30'
set high-availability vrrp global-parameters notification smtp-server port '25'
set high-availability vrrp global-parameters notification source-mail '[email protected]'
set high-availability vrrp global-parameters router-id 'MYROUTER'

In T5048#143916, @Viacheslav wrote:

As I understand there no percent or auto and it now expects only rate, needs to check

vyos@r14# set qos policy shaper test default bandwidth
Possible completions:
   <number>             Bits per second
   <number>bit          Bits per second
   <number>kbit         Kilobits per second
   <number>mbit         Megabits per second
   <number>gbit         Gigabits per second
   <number>tbit         Terabits per second
   <number>

I don't know why when I set bandwidth from 10k-10mbit/s, the QoS shaper works correctly but when I set to 100mbit/s~600mbit/s, I only get fews of mbit/s or tens of mbit/s. When I set above about 800mbit/s it looks like no limitation at all. When I manually set limit by tc commands, it seems okay.

As I understand there no percent or auto and it now expects only rate, needs to check

vyos@r14# set qos policy shaper test default bandwidth
Possible completions:
   <number>             Bits per second
   <number>bit          Bits per second
   <number>kbit         Kilobits per second
   <number>mbit         Megabits per second
   <number>gbit         Gigabits per second
   <number>tbit         Terabits per second
   <number>

I don't know why I set a 100mbit/s shaper, but result in lots of retry and 5~10mbit/s speed.

In T5048#143912, @Viacheslav wrote:

Try the latest rolling release

@Jimz Which lease time are you useing?

starts 5 2023/03/03 02:09:13;
ends never;

With default config I see something like

lease 192.0.2.10 {
  starts 5 2023/03/03 08:07:15;
  ends 6 2023/03/04 08:07:15;
...

Try the latest rolling release

I have almost same problem here. Can't NAT between two VRFs correctly. The outgoing packet has been NATed correctly but the incoming packet seems be dropped, can't reach the source, it seems the return packet can't be tracked correctly.

sh dhcp server leases
Traceback (most recent call last):

File "/usr/libexec/vyos/op_mode/dhcp.py", line 286, in <module>
  res = vyos.opmode.run(sys.modules[__name__])
        ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
File "/usr/lib/python3/dist-packages/vyos/opmode.py", line 227, in run
  res = func(**args)
        ^^^^^^^^^^^^
File "/usr/libexec/vyos/op_mode/dhcp.py", line 246, in _wrapper
  return func(*args, **kwargs)
         ^^^^^^^^^^^^^^^^^^^^^
File "/usr/libexec/vyos/op_mode/dhcp.py", line 277, in show_server_leases
  lease_data = _get_raw_server_leases(family=family, pool=pool, sorted=sorted, state=state)
               ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
File "/usr/libexec/vyos/op_mode/dhcp.py", line 85, in _get_raw_server_leases
  data_lease['end'] = lease.end.timestamp()
                      ^^^^^^^^^^^^^^^^^^^

AttributeError: 'NoneType' object has no attribute 'timestamp'

After the first lease I got the same error:

Btw, in this rolling release, OSPF BFD in tunnel doesn't work correctly too.

You can manually modify strongswan's systemd service file to add 'ip vrf exec charond'. But it causes other problem.

I backed up /config/dhcpd.leases - replaced it with an empty file. And it appears to be working, the /config/dhcpd.leases file seems to have been corrupted or malformated.

Is there a way to share it privately? It has some of the internal domains and leases.

PR https://github.com/vyos/vyos-1x/pull/1865
We found some issues for the migration and we fixed it on this one.